2013 and 2014 Ford Econoline E-series remote head key keyless entry fob alarm programming information

Once the key has been cut by a Ford dealer a locksmith, you can program this 2013 or 2014 Ford Econoline E-series remote key yourself at home IF YOU HAVE TWO WORKING/PROGRAMMED KEYS already.
If you do not have two working/programmed keys, you will have to take this remote key to a dealer or locksmith for programming.

Please read and understand the
entire procedure before you begin.
1. Insert the first previously
programmed coded key into the
ignition.
2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
3. Turn the ignition to the 1 (LOCK) position and remove the first coded
key from the ignition.
4. Within ten seconds of turning the ignition to the 1 (LOCK) position,
insert the second previously coded key into the ignition.
5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
6. Turn the ignition to the 1 (LOCK) position and remove the second
previously programmed coded key from the ignition.
7. Within twenty seconds of turning the ignition to the 1 (LOCK)
position and removing the previously programmed coded key, insert the
new unprogrammed key (new key/valet key) into the ignition.
8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least six seconds.
9. Remove the newly programmed coded key from the ignition.
If the key has been successfully programmed it will start the vehicle’s
engine and will operate the remote entry system (if the new key is an
Integrated Keyhead Transmitter). The theft indicator light will illuminate
for three seconds and then go out to indicate successful programming.

Free Programming instructions for 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Ford Econoline E-Series remote keyless entry fob alarm

How to program your 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Ford Econoline E-Series remote keyless entry fob alarm by yourself at home without going to the dealer.
There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 1992, 1993, 1994, 1995, and 1996 (also 1997, 1998 and 1999 Old type system) Ford Econoline E-Series remote keyless entry fob alarm

How to program your 1992, 1993, 1994, 1995, and 1996 (also 1997, 1998 and 1999 Old type system) Ford Econoline E-Series remote keyless entry fob alarm by yourself at home without going to the dealer.

Obtain All remote transmitters
Access programming connector located below fascia at the base of the steering column
Switch Ignition ON
Jump program connector
*Doors should lock and unlock
Press any button on the remote transmitter
*Doors should lock and unlock
Press any button on the second remote transmitter
*Doors should lock and unlock
Press any button on Third the remote transmitter
*Doors should lock and unlock
Press any button on the Fourth remote transmitter
***Note: if door locks do not operate: Press button again up to a maximum of 3 times
Switch ignition OFF
Remove jumper wire
*Doors should lock and unlock to exit programming mode

Free Programming instructions for 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, and 2011 Ford Crown Victoria remote keyless entry fob alarm

How to program your 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, and 2011 Ford Crown Victoria remote keyless entry fob alarm by yourself at home without going to the dealer.

Turn the ignition from OFF to RUN 4 times within 3 seconds, with the 4th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 1993, 1994, 1995, 1996, and 1997 Ford Crown Victoria remote keyless entry fob alarm

How to program your 1993, 1994, 1995, 1996, and 1997 Ford Crown Victoria remote keyless entry fob alarm by yourself at home without going to the dealer.

programming connector
Obtain all remote transmitters
Access programming connector, located behind the glove box and taped to the wiring harness
Switch ignition ON
Momentarily jump programming connector
*Doors should lock and unlock
Remove jump wire from connector
Press any button on first remote transmitter
*doors should lock and unlock
Press any button on additional transmitter
*doors should lock and unlock
(repeat this step for up to 4 transmitters)
** If doors do not lock and unlock.. press button on transmitter up to 3 times
Switch ignition OFF
*Doors should lock and unlock to exit programming mode.

Free Programming instructions for 1995, 1996, 1997, 1998, 1999, 2000, 2001, and 2002 Ford Contour remote keyless entry fob alarm

How to program your 1995, 1996, 1997, 1998, 1999, 2000, 2001, and 2002 Ford Contour remote keyless entry fob alarm by yourself at home without going to the dealer.

programming connector
Obtain all remote transmitters
Access programming connector, located behind the glove box and taped to the wiring harness
Switch ignition ON
Momentarily jump programming connector
*Doors should lock and unlock
Remove jump wire from connector
Press any button on first remote transmitter
*doors should lock and unlock
Press any button on additional transmitter
*doors should lock and unlock
(repeat this step for up to 4 transmitters)
** If doors do not lock and unlock.. press button on transmitter up to 3 times
Switch ignition OFF
*Doors should lock and unlock to exit programming mode.

Free Programming instructions for 1994, 1995, and 1996 Ford Bronco remote keyless entry fob alarm

How to program your 1994, 1995, and 1996 Ford Bronco remote keyless entry fob alarm by yourself at home without going to the dealer.

programming connector

Obtain all remote transmitters
Access programming connector, taped to the wiring harness near to the central locking control module located behind the LH fascia (see figure above)
Switch ignition ON
Momentarily jump programming connector
*Doors should lock and unlock
Remove jump wire from connector
Press any button on first remote transmitter
*doors should lock and unlock
Press any button on additional transmitter
*doors should lock and unlock
(repeat this step for up to 4 transmitters)
** If doors do not lock and unlock.. press button on transmitter up to 3 times
Switch ignition OFF
*Doors should lock and unlock to exit programming mode.

Free Programming instructions for 2003, 2004, 2005, 2006, 2007, 2008, and 2009 Dodge Viper remote keyless entry fob alarm

How to program your 2003, 2004, 2005, 2006, 2007, 2008, and 2009 Dodge Viper remote keyless entry fob alarm

**YOU MUST HAVE A WORKING/PROGRAMMED REMOTE IN ORDER TO PROGRAM A NEW REMOTE TO THE CAR**
**if you do not have a working remote now.. you must take the new remote to a dealer or locksmith for programming

1. Press (LOCK) button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.
2. Turn ignition to run position. (Allow ignition chimes [UNLOCK] to stop).
3. Using any original (working) transmitter, press the [UNLOCK] button for 4 to 10 seconds.
4. Within the specified 4 to 10 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons . A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).
5. (USE PURCHASED REMOTE) Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release (a short chime may sound).
6. Press and release any button on the same transmitter and a chime will sound after successfully programming the transmitter (locks may cycle).
NOTE: A CHIME WILL NOT SOUND ON STEP # 6 FOR THE FIRST TRANSMITTER PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.
7. (YOU MUST REPROGRAM ALL ORIGINAL REMOTES) Repeat steps 5 through 6 to program additional transmitters.
8. Turn ignition to OFF position. Transmitter programming mode will discontinue after 60 seconds . (All transmitter programming must be completed within time specified).

To order a remote or to learn more about this product, please click on the link below:

http://www.carandtruckremotes.com/dodge-remotes-viper-remotes.html