Free Programming instructions for 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, and 2010 Mercury Mountaineer remote keyless entry fob alarm

How to program your 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, and 2010 Mercury Mountaineer remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible)
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 1995, 1996, and 1997 Mercury Mountaineer remote keyless entry fob alarm

How to program your 1995, 1996, and 1997 Mercury Mountaineer remote keyless entry fob alarm by yourself at home without going to the dealer.

Turn ignition from OFF to RUN (as far as you can go without cranking the engine) 5 times within 10 seconds, with the 5th time ending in RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds, press any button on 1st remote transmitter.
Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn ignition to OFF.
Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 1993 and 1994 Mercury Mountaineer remote keyless entry fob alarm

How to program your 1993 and 1994 Mercury Mountaineer remote keyless entry fob alarm by yourself at home without going to the dealer.

Obtain all remote transmitters
Access program connector taped to the wiring harness located in trunk (LH)
Switch ignition ON
Momentarily jump program connector terminals
(NOTE: The program connector is located in the trunk, behind the rear left hand access panel, taped to the wiring harness between the left tail light and he rear left wheel well.)
Door should lock then unlock
Remove jump wire program connector
Press any button on the first remote transmitter
Doors should lock then unlock
Press any button on the second remote transmitter
Doors should lock then unlock
Press any button on the third remote transmitter
Doors should lock then unlock
Press any button on the fourth remote transmitter
Doors should lock then unlock

Note: if door locks do not operate: press button again up to a maximum of 3 times

Switch ignition OFF:
Doors should lock then unlock

Note: a maximum of 4 remote transmitters can be programmed

Free Programming instructions for 2004, 2005, 2006, and 2007 Mercury Monterey remote keyless entry fob alarm

How to program your 2004, 2005, 2006, and 2007 Mercury Monterey remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Be sure Brake Pedal is not depressed while performing procedure.
Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible on 2004 and 2005 models; up to 6 on 2006 and 2007 models).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 2005, 2006, and 2007 Mercury Montego remote keyless entry fob alarm

How to program your 2005, 2006, and 2007 Mercury Montego remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Be sure Brake Pedal is not depressed while performing procedure.
Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible on 2005; up to 6 on 2006 and 2007 models).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

2007, 2008, 2009, 2010, and 2011 Mercury Milan IKT remote head key keyless entry fob alarm free programming instructions

Once the key has been cut by a Mercury or Ford dealer or a locksmith, you can program the 2007, 2008, 2009, 2010, and 2011 Mercury Milan IKT remote key yourself at home IF YOU HAVE TWO WORKING/PROGRAMMED KEYS already.
If you do not have two working/programmed keys, you will have to take this remote key to a dealer or locksmith for programming.

Please read and understand the
entire procedure before you begin.
1. Insert the first previously
programmed coded key into the
ignition.
2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
3. Turn the ignition to the 1 (LOCK) position and remove the first coded
key from the ignition.
4. Within ten seconds of turning the ignition to the 1 (LOCK) position,
insert the second previously coded key into the ignition.
5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
6. Turn the ignition to the 1 (LOCK) position and remove the second
previously programmed coded key from the ignition.
7. Within twenty seconds of turning the ignition to the 1 (LOCK)
position and removing the previously programmed coded key, insert the
new unprogrammed key (new key/valet key) into the ignition.
8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least six seconds.
9. Remove the newly programmed coded key from the ignition.
If the key has been successfully programmed it will start the vehicle’s
engine and will operate the remote entry system (if the new key is an
Integrated Keyhead Transmitter). The theft indicator light will illuminate
for three seconds and then go out to indicate successful programming.

Free Programming instructions for 2006 Mercury Milan remote keyless entry fob alarm

How to program your 2006 Mercury Milan remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

2007, 2008, 2009, 2010, and 2011 Mercury Mariner IKT remote head key keyless entry fob alarm free programming instructions

Once the key has been cut by a Mercury or Ford dealer or a locksmith, you can program the 2007, 2008, 2009, 2010, and 2011 Mercury Mariner IKT remote key yourself at home IF YOU HAVE TWO WORKING/PROGRAMMED KEYS already.
If you do not have two working/programmed keys, you will have to take this remote key to a dealer or locksmith for programming.

Please read and understand the
entire procedure before you begin.
1. Insert the first previously
programmed coded key into the
ignition.
2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
3. Turn the ignition to the 1 (LOCK) position and remove the first coded
key from the ignition.
4. Within ten seconds of turning the ignition to the 1 (LOCK) position,
insert the second previously coded key into the ignition.
5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
6. Turn the ignition to the 1 (LOCK) position and remove the second
previously programmed coded key from the ignition.
7. Within twenty seconds of turning the ignition to the 1 (LOCK)
position and removing the previously programmed coded key, insert the
new unprogrammed key (new key/valet key) into the ignition.
8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least six seconds.
9. Remove the newly programmed coded key from the ignition.
If the key has been successfully programmed it will start the vehicle’s
engine and will operate the remote entry system (if the new key is an
Integrated Keyhead Transmitter). The theft indicator light will illuminate
for three seconds and then go out to indicate successful programming.

Free Programming instructions for 2005 and 2006 Mercury Mariner remote keyless entry fob alarm

How to program your 2005 and 2006 Mercury Mariner remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 2007, 2008, 2009, 2010, and 2011 Mercury Grand Marquis remote keyless entry fob alarm

How to program your 2007, 2008, 2009, 2010, and 2011 Mercury Grand Marquis remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.