2014, 2015, and 2016 Jeep Cherokee remote keyless entry fob alarm programming information

Unfortunately, there are no do it yourself instructions that will work to program the 2014, 2015, and 2016 Jeep Cherokee key less entry remote fobs, fobiks.
This remote must be programmed by a Jeep dealer or a professional automotive locksmith.

To order a remote or for more information, click on the link below:

http://www.carandtruckremotes.com/jeep-remotes–cherokee-remotes.html

1996, 1997, 1998, 1999, 2000, 2001, and 2002 Chevy Camaro FREE do it yourself remote keyless entry fob programming instructions

Here are some simple instructions that will tell you how to program your 1996, 1997, 1998, 1999, 2000, 2001, and 2002 Chevrolet Camaro keyless entry remote fob yourself at home without going to the dealer!

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

Be sure ignition is OFF
Remove Radio Fuse (number 17) from fuse box (Located at LH end of instrument panel)
Switch ignition from OFF to RUN 3 times (ending in the Run position) (3 times within 5 seconds)
Doors will lock and then unlock indicating that programming mode is active
* Press and hold LOCK and UNLOCK at the same time on the remote for up to 15 seconds or until the car responds by locking and unlocking again
* Repeat the last step for each additional remote
Switch ignition OFF
Refit Radio fuse

To order a remote or for more information, click on the link below:
http://www.carandtruckremotes.com/chevrolet-remotes-camaro-remotes.html

Free programming information for 2012, 2013, 2014, and 2015 Toyota Yaris remote keyless entry fob remote head key alarm key

Unfortunately, there are no do it yourself instructions that will work to program the 2012, 2013, 2014, and 2015 Toyota Yaris remote head key.
This remote must be programmed by a Toyota dealer or a professional automotive locksmith.

For more information about these remote keys or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-yaris-remotes.html

2007, 2008, 2009, 2010, and 2011 Toyota Yaris Free programming instructions for remote head key keyless entry remote fob alarm

You can program the remote portion of your 2007, 2008, 2009, 2010, and 2011 Toyota Yaris remote key yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Toyota Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

Driver’s door open, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.
Within 40 seconds:
Close and open driver’s door twice.
Insert and remove the key from the ignition switch.
Within 40 seconds:
Close and open driver’s door twice.
Insert the key into the ignition switch and close the driver’s door.
Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program a remote transmitter code whilst erasing the original codes.
Remove key from ignition switch:
System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered.
Within 40 seconds:
Press and hold LOCK and UNLOCK remote buttons simultaneously for 1.5 seconds
Within 3 seconds:
Press LOCK button.
System should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed.
Within 40 seconds:
Repeat button procedure to program remaining remote transmitters.
NOTE: To exit programming mode: Open driver’s door. NOTE: A maximum of 4 remote transmitters can be programmed.

For more information about these remote keys or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-yaris-remotes.html

2009, 2010, 2011, 2012, 2013, and 2014 Toyota Venza Free programming instructions for remote head key keyless entry remote fob alarm

You can program the remote portion of your 2009, 2010, 2011, 2012, 2013, and 2014 Toyota Venza remote key yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Toyota Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

Driver’s door open, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.
Within 40 seconds:
Close and open driver’s door twice.
Insert and remove the key from the ignition switch.
Within 40 seconds:
Close and open driver’s door twice.
Insert the key into the ignition switch and close the driver’s door.
Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program a remote transmitter code whilst erasing the original codes.
Remove key from ignition switch:
System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered.
Within 40 seconds:
Press and hold LOCK and UNLOCK remote buttons simultaneously for 1.5 seconds
Within 3 seconds:
Press LOCK button.
System should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed.
Within 40 seconds:
Repeat button procedure to program remaining remote transmitters.
NOTE: To exit programming mode: Open driver’s door. NOTE: A maximum of 4 remote transmitters can be programmed.

For more information about these remote/keys or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-venza-remotes.html

Free programming information for 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, and 2016 Toyota Tundra remote fob alarm keyless entry remote key

Unfortunately, there are no do it yourself programming instructions that will work for the 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, and 2016 Toyota Tundra remote keyless entry fob alarm.
You must take this remote to a Toyota dealer or local automotive locksmith for programming.

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tundra-remotes.html

2004, 2005, and 2006 Toyota Tundra (Factory Installed) free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2004, 2005, and 2006 Toyota Tundra (Factory Installed) replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a video below the written instructions that shows how easy this is done.

Driver’s door open, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.
Within 40 seconds:
Close and open driver’s door twice.
Insert and remove the key from the ignition switch.
Within 40 seconds:
Close and open driver’s door twice.
Insert the key into the ignition switch and close the driver’s door.
Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program a remote transmitter code whilst erasing the original codes.
Remove key from ignition switch:
System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered.
Within 40 seconds:
Press and hold LOCK and UNLOCK remote buttons simultaneously for 1.5 seconds
Within 3 seconds:
Press LOCK button.
System should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed.
Within 40 seconds:
Repeat button procedure to program remaining remote transmitters.
NOTE: To exit programming mode: Open driver’s door. NOTE: A maximum of 4 remote transmitters can be programmed.

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tundra-remotes.html

2002, 2003, and 2004 Toyota Tacoma (Dealer installed) free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2002, 2003, and 2004 Toyota Tacoma (Dealer installed) replacement remote keyless entry fob alarm by yourself at home without going to the dealer. This is for the dealer installed remote keyless system.

MPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes

1. Driver’s door open, all other doors closed, key removed from ignition switch
2. Insert key into ignition switch, then remove it
3. Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.
4. Close and reopen driver’s door
5. Press LOCK and UNLOCK on the vehicle door lock control at 1 second intervals 5 times.
6. Insert key into ignition switch
7. Switch ignition ON and OFF once to program a remote code while retaining the original codes, twice to program a remote transmitter code while erasing the original codes. Three times to check how many remote transmitters are currently registered or five times to erase all codes
8. Remove key from ignition switch. System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. One to 4 times slowly, to indicate number of remotes registered
9. Press and hold remote LOCK button and UNLOCK buttons together for 1-1.5 second
10. Press LOCK remote button for 1 second: system should lock and unlock vehicle one to confirm, twice to indicate registration has failed
11. If required repeat button procedure to program remaining remotes
NOTE To exit programming mode – close drivers door or insert ignition key

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tacoma-remotes.html

2000, 2001, and 2002 Toyota Tundra free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2000, 2001, and 2002 Toyota Tundra replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

I. To program (add) a REMOTE CONTROL to the system:
1. Insert the key into ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and release a REMOTE
CONTROL’s top or bottom
button.*
The STATUS MONITOR LED
turns off.
The Piezo “chirper” chirps once.
The exterior lights flash once.
4. Turn off the ignition. The ECU will
now operate with the REMOTE
CONTROL just programmed.
* Either button on your REMOTE CONTROL can be programmed to operate the system. The bottom
button can be programmed to operate a second vehicle with the Toyota VIP.
Programming
Procedure
Press and Hold
for 3 Seconds
Lights Up
Press Once

II. To erase all REMOTE CONTROL codes from the system:
1. Insert key into the ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and hold the ECU’s
PROGRAMMING SWITCH for
over 2 seconds again.
The STATUS MONITOR LED
turns off, then flashes 3 times.
The Piezo “chirper” chirps three
times and the exterior lights flash
3 times.
4. Turn off the ignition. The ECU has cleared all REMOTE CONTROL codes; until
another REMOTE CONTROL is programmed, the system will not work with any
REMOTE CONTROL.

rs3000_alarmbrain

rs3000_greenbutton

rs3000_ignition_off

rs3000_ignition_on

rs3000_remote

rs3000_securityled

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tundra-remotes.html

1993, 1994, 1995, 1996, 1997, and 1998 Toyota Tercel free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1993, 1994, 1995, 1996, 1997, and 1998 Toyota Tercel replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

I. To program (add) a REMOTE CONTROL to the system:
1. Insert the key into ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and release a REMOTE
CONTROL’s top or bottom
button.*
The STATUS MONITOR LED
turns off.
The Piezo “chirper” chirps once.
The exterior lights flash once.
4. Turn off the ignition. The ECU will
now operate with the REMOTE
CONTROL just programmed.
* Either button on your REMOTE CONTROL can be programmed to operate the system. The bottom
button can be programmed to operate a second vehicle with the Toyota VIP.
Programming
Procedure
Press and Hold
for 3 Seconds
Lights Up
Press Once

II. To erase all REMOTE CONTROL codes from the system:
1. Insert key into the ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and hold the ECU’s
PROGRAMMING SWITCH for
over 2 seconds again.
The STATUS MONITOR LED
turns off, then flashes 3 times.
The Piezo “chirper” chirps three
times and the exterior lights flash
3 times.
4. Turn off the ignition. The ECU has cleared all REMOTE CONTROL codes; until
another REMOTE CONTROL is programmed, the system will not work with any
REMOTE CONTROL.

rs3000_alarmbrain

rs3000_greenbutton

rs3000_ignition_off

rs3000_ignition_on

rs3000_remote

rs3000_securityled

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tercel-remotes.html