1996, 1997, 1998, 1999, 2000, 2001, and 2002 Chevy Camaro FREE do it yourself remote keyless entry fob programming instructions

Here are some simple instructions that will tell you how to program your 1996, 1997, 1998, 1999, 2000, 2001, and 2002 Chevrolet Camaro keyless entry remote fob yourself at home without going to the dealer!

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

Be sure ignition is OFF
Remove Radio Fuse (number 17) from fuse box (Located at LH end of instrument panel)
Switch ignition from OFF to RUN 3 times (ending in the Run position) (3 times within 5 seconds)
Doors will lock and then unlock indicating that programming mode is active
* Press and hold LOCK and UNLOCK at the same time on the remote for up to 15 seconds or until the car responds by locking and unlocking again
* Repeat the last step for each additional remote
Switch ignition OFF
Refit Radio fuse

To order a remote or for more information, click on the link below:
http://www.carandtruckremotes.com/chevrolet-remotes-camaro-remotes.html

1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, and 2005 Chevrolet Venture Van free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, and 2005 Chevy Venture Van replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

1. Remove the ignition key from the ignition lock cylinder.

2. Remove the “BCM PRGRM” fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the “BCMPRGRM” fuse.

3. Close all of the doors.
4. Close the liftgate.

5. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you – the opposite direction from starting the engine).

6. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second (the quicker the better)

7. Open and close any vehicle door. A chime will be heard when the system enters the programming mode.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming. Your new remote has been accepted and all existing remote codes have been erased.

9. Repeat the previous step on each additional transmitter to be programmed (including any existing transmitters). Just repeat step #9 for each remote you want to
program. Don’t repeat all nine steps for each remote

10. Remove the ignition key from the ignition lock cylinder.

11. Install the “BCM PRGRM” fuse back into the fuse panel.

2009 and 2010 Chevrolet Traverse free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2009 and 2010 Chevrolet Traverse replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a free programming tutorial video below to show you how easy it is done.


Switch ignition ON.
Repeatedly press vehicle information button Fig. 2 [A] until PRESS TO RELEARN REMOTE KEY is displayed.
Press set/reset button Fig. 2 [B] until REMOTE KEY LEARNING ACTIVE is displayed.
Programming mode activated, proceed as follows:
Press and hold LOCK and UNLOCK buttons on first remote transmitter simultaneously for 15 seconds.
Wait for acoustic signal (indicates correct programming).
Repeat above procedure to program remaining remote transmitters.
Switch ignition OFF to exit programming mode.
Remote transmitters can also be programmed using diagnostic equipment.
NOTE: A maximum of 8 remote transmitters can be programmed.

Chevrolet Trailblazer 2002, 2003, 2004, 2005, 2006, 2007, 2008, and 2009 free programming instructions for replacement remote keyless entry fob alarm

This is how to program your Chevrolet Trailblazer 2002, 2003, 2004, 2005, 2006, 2007, 2008, or 2009 replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

1999, 2000, 2001, 2002, 2003 and 2004 Chevy Tracker free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1999, 2000, 2001, 2002, 2003 and 2004 Chevy Tracker replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

1. Locate the Data Line Connector (DLC) underneath the driver’s side dashboard. Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
Use a jumper wire
to connect pins 4 & 8

2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (you can use a piece of thin electrical cable, speaker cable or simply U shaped paper clip; leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by cycling the locks (locking then unlocking doors) to signify entering of programming mode.
Figure a. Data link connector
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).

Free do it yourself remote programming instructions for 2007, 2008, 2009 and 2010 Chevrolet Tahoe replacement keyless entry remote fob alarm

This is how to program your remote keyless entry fob for the 2000, 2001, 2002, 2003, 2004, 2005, and 2006 (with and without remote start option) Chevy Tahoe.
There is also a free programming tutorial video below to show you how easy it is done.



Switch ignition ON.
Repeatedly press vehicle information button Fig. 2 [A] until PRESS TO RELEARN REMOTE KEY is displayed.
Press set/reset button Fig. 2 [B] until REMOTE KEY LEARNING ACTIVE is displayed.
Programming mode activated, proceed as follows:
Press and hold LOCK and UNLOCK buttons on first remote transmitter simultaneously for 15 seconds.
Wait for acoustic signal (indicates correct programming).
Repeat above procedure to program remaining remote transmitters.
Switch ignition OFF to exit programming mode.
Remote transmitters can also be programmed using diagnostic equipment.
NOTE: A maximum of 8 remote transmitters can be programmed.

Free do it yourself remote programming instructions for 2000, 2001, 2002, 2003, 2004, 2005, and 2006 Chevrolet Tahoe replacement keyless entry remote fob alarm

This is how to program your remote keyless entry fob for the 2000, 2001, 2002, 2003, 2004, 2005, and 2006 (new body style) Chevy Tahoe
There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

Free do it yourself remote programming instructions for 1997, 1998, 1999, and 2000 Chevrolet Tahoe replacement keyless entry remote fob alarm

This is how to program your remote keyless entry fob for the 1997, 1998, 1999 and 2000 (old body style) Chevy Tahoe

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

1. Locate the Data Line Connector (DLC) underneath the driver’s side dashboard. Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
Use a jumper wire
to connect pins 4 & 8

2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (you can use a piece of thin electrical cable, speaker cable or simply U shaped paper clip; leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by cycling the locks (locking then unlocking doors) to signify entering of programming mode.
Figure a. Data link connector
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).