Free Programming instructions for 1998.5, 1999, 2000, 2001, 2002, and 2003 Ford Windstar Van Minivan remote keyless entry fob alarm

How to program your 1998.5, 1999, 2000, 2001, 2002, and 2003 Ford Windstar Van Minivan remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 1998 Ford Windstar remote keyless entry fob alarm van minivan

How to program your 1998 Ford Windstar pickup truck remote keyless entry fob alarm by yourself at home without going to the dealer.

Turn the ignition from OFF to RUN 5 times within 10 seconds, with the 5th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

**If you have remotes with Memory 1 and Memory 2 be sure to program Memory 1 remote first and Memory 2 remote second.

Van Minivan

Free Programming instructions for 1995, 1996, and 1997 Ford Windstar remote keyless entry fob alarm Van Minivan

How to program your 1995, 1996, and 1997 Ford Windstar remote keyless entry fob alarm by yourself at home without going to the dealer.

Obtain all remote transmitters
Access program connector behind the glove box and taped to the wiring harness.
Switch ignition ON
Momentarily jump program connector terminals
Door should lock then unlock
Remove jump wire program connector
Press any button on the first remote transmitter
Doors should lock then unlock
Press any button on the second remote transmitter
Doors should lock then unlock
Press any button on the third remote transmitter
Doors should lock then unlock
Press any button on the fourth remote transmitter
Doors should lock then unlock

Note: if door locks do not operate: press button again up to a maximum of 3 times

Switch ignition OFF:
Doors should lock then unlock

Note: a maximum of 4 remote transmitters can be programmed

Van Minivan

Free Programming instructions for 2002, 2003, 2004, 2005, and 2006 Ford Thunderbird remote keyless entry fob alarm

How to program your 2002, 2003, 2004, 2005, and 2006 Ford Thunderbird remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 1993, 1994, 1995, 1996 and 1997 Ford Thunderbird remote keyless entry fob alarm

How to program your 1993, 1994, 1995, 1996 and 1997 Ford Thunderbird remote keyless entry fob alarm by yourself at home without going to the dealer.


Obtain all remote transmitters
Access program connector taped to the wiring harness located in trunk (LH)
Switch ignition ON
Momentarily jump program connector terminals
Door should lock then unlock
Remove jump wire program connector
Press any button on the first remote transmitter
Doors should lock then unlock
Press any button on the second remote transmitter
Doors should lock then unlock
Press any button on the third remote transmitter
Doors should lock then unlock
Press any button on the fourth remote transmitter
Doors should lock then unlock

Note: if door locks do not operate: press button again up to a maximum of 3 times

Switch ignition OFF:
Doors should lock then unlock

Note: a maximum of 4 remote transmitters can be programmed

2008, 2009, 2010, 2011, 2012, 2013, and 2014 Ford Taurus and Ford Taurus X IKT remote head key keyless entry fob alarm free programming instructions

Once the key has been cut by a Ford dealer or a locksmith, you can program the 2008, 2009, 2010, 2011, 2012, 2013, and 2014 Ford Taurus and Ford Taurus X remote key yourself at home IF YOU HAVE TWO WORKING/PROGRAMMED KEYS already.
If you do not have two working/programmed keys, you will have to take this remote key to a dealer or locksmith for programming.

Please read and understand the
entire procedure before you begin.
1. Insert the first previously
programmed coded key into the
ignition.
2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
3. Turn the ignition to the 1 (LOCK) position and remove the first coded
key from the ignition.
4. Within ten seconds of turning the ignition to the 1 (LOCK) position,
insert the second previously coded key into the ignition.
5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
6. Turn the ignition to the 1 (LOCK) position and remove the second
previously programmed coded key from the ignition.
7. Within twenty seconds of turning the ignition to the 1 (LOCK)
position and removing the previously programmed coded key, insert the
new unprogrammed key (new key/valet key) into the ignition.
8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least six seconds.
9. Remove the newly programmed coded key from the ignition.
If the key has been successfully programmed it will start the vehicle’s
engine and will operate the remote entry system (if the new key is an
Integrated Keyhead Transmitter). The theft indicator light will illuminate
for three seconds and then go out to indicate successful programming.

Free Programming instructions for 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, and 2007 Ford Taurus remote keyless entry fob alarm

How to program your 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, and 2007 Ford Taurus remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free Programming instructions for 1996 and 1997 Ford Taurus remote keyless entry fob alarm

How to program your 1996 and 1997 Ford Taurus pickup truck remote keyless entry fob alarm by yourself at home without going to the dealer.

Turn the ignition from OFF to RUN 5 times within 10 seconds, with the 5th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

**If you have remotes with Memory 1 and Memory 2 be sure to program Memory 1 remote first and Memory 2 remote second.