Free remote programming instructions for your 2007, 2008, 2009, and 2010 GMC Yukon Denali keyless entry remote fob

You can program your 2007, 2008, 2009, and 2010 GMC Yukon Denali remote yourself at home with these simple instructions.

There is also a free programming tutorial video below to show you how easy it is done.


Switch ignition ON.
Press vehicle information button Fig. 2 [A] until PRESS TO RELEARN REMOTE KEY is displayed.
Press set/reset button Fig. 2 [B] until REMOTE KEY LEARNING ACTIVE is displayed.
Programming mode activated, proceed as follows:
Press and hold LOCK and UNLOCK buttons on first remote transmitter simultaneously for 15 seconds.
Wait for acoustic signal (indicates correct programming).
Repeat above procedure to program remaining remote transmitters.
Switch ignition OFF to exit programming mode.
Remote transmitters can also be programmed using diagnostic equipment.
NOTE: A maximum of 8 remote transmitters can be programmed.

Free programming instructions for 2000, 2001, 2002, 2003, 2004, 2005, and 2006 GMC Yukon Denali replacement remote keyless entry fob alarm

This is how to program your 2000, 2001, 2002, 2003, 2004, 2005, and 2006 GMC Yukon Denali replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

Free programming instructions for 1997, 1998, 1999, and 2000 GMC Yukon replacement remote keyless entry fob alarm

This is how to program your 1997, 1998, 1999, and 2000 GMC Yukon replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.
1. Locate the Data Line Connector (DLC) underneath the driver’s side dashboard. Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (you can use a piece of thin electrical cable, speaker cable or simply U shaped paper clip; leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by cycling the locks (locking then unlocking doors) to signify entering of programming mode.
Use a jumper wire to connect pins 4 & 8
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
Figure a. Data link connector
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).

Free programming instructions for 1997, 1998, and 1999 GMC Suburban replacement remote keyless entry fob alarm

This is how to program your 1997, 1998, and 1999 GMC Suburban replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.
1. Locate the Data Line Connector (DLC) underneath the driver’s side dashboard. Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (you can use a piece of thin electrical cable, speaker cable or simply U shaped paper clip; leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by cycling the locks (locking then unlocking doors) to signify entering of programming mode.
Use a jumper wire to connect pins 4 & 8
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
Figure a. Data link connector
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).

Free programming instructions for 1998, 1999, 2000, 2001, 2002, 2003, and 2004 GMC Sonoma replacement remote keyless entry fob alarm

This is how to program your 1998, 1999, 2000, 2001, 2002, 2003, and 2004 GMC Sonoma replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

1997 GMC Sonoma keyless entry remote fob alarm free programming instructions

You can program your 1997 GMC Sonoma remote yourself at home with these simple instructions.

Up to two remotes can be programmed (be sure to have both with you at time of programming)
Access the two red wired programming connector (located near the central locking module, behind LH lower instrumental panel)
Jump programming connector terminals
System should now lock and unlock doors to indicate programming mode actives
Proceed as follows:
*Press any button on remote transmitter once
*System should now lock and unlock doors indicating that the remote is programmed
Repeat last two steps for the second remote (if you have one)
Remove programming connector jump to exit programming mode

2011, 2012, 2013, and 2014 GMC Sierra Pickup Truck (including 1500, 2500, and 3500 models) keyless entry remote fob free programming information

Unfortunately, there are no do it yourself instructions that will work to program the 2011, 2012, 2013, and 2014 GMC Sierra Pickup Truck (including 1500, 2500, and 3500 models) keyless entry remote.
This remote must be programmed by a Chevy/GM/GMC dealer or a professional automotive locksmith.

Free remote programming instructions for your 2008, 2009, 2010 GMC Sierra Pickup Truck (including 1500, 2500, and 3500 models) keyless entry remote fob

You can program your 2008, 2009, 2010 GMC Sierra Pickup Truck (including 1500, 2500, and 3500 models) remote yourself at home with these simple instructions.

There is also a free programming tutorial video below to show you how easy it is done.

Switch ignition ON.
Press vehicle information button Fig. 2 [A] until PRESS TO RELEARN REMOTE KEY is displayed.
Press set/reset button Fig. 2 [B] until REMOTE KEY LEARNING ACTIVE is displayed.
Programming mode activated, proceed as follows:
Press and hold LOCK and UNLOCK buttons on first remote transmitter simultaneously for 15 seconds.
Wait for acoustic signal (indicates correct programming).
Repeat above procedure to program remaining remote transmitters.
Switch ignition OFF to exit programming mode.
Remote transmitters can also be programmed using diagnostic equipment.
NOTE: A maximum of 8 remote transmitters can be programmed.

Free programming instructions for 1999 (new body style), 2000, 2001, 2002, 2003, 2004, 2005, 2006, and 2007 GMC Sierra Pickup Truck replacement remote keyless entry fob alarm (including 1500, 2500, and 3500 models)

This is how to program your 1999 (new body style), 2000, 2001, 2002, 2003, 2004, 2005, 2006, and 2007 GMC Sierra Pickup Truck replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
Including 1500, 2500, and 3500 model trucks.

There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.