1997, 1998, and 1999 (old body style) GMC Sierra Pickup Truck free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1997, 1998, and 1999 (old body style) GMC Sierra Pickup Truck replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

1. Locate the Data Line Connector (DLC) underneath the driver’s side dashboard. Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
Use a jumper wire
to connect pins 4 & 8

2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (you can use a piece of thin electrical cable, speaker cable or simply U shaped paper clip; leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by cycling the locks (locking then unlocking doors) to signify entering of programming mode.
Figure a. Data link connector
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).

2011, 2012, 2013, and 2014 GMC Savana Van (including 1500, 2500, and 3500 models) keyless entry remote fob free programming information

Unfortunately, there are no do it yourself instructions that will work to program the 2011, 2012, 2013, and 2014 GMC Savana Van (including 1500, 2500, and 3500 models) keyless entry remote.
This remote must be programmed by a Chevy/GM/GMC dealer or a professional automotive locksmith.

Free remote programming instructions for your 2008, 2009, 2010 GMC Savana Van (including 1500, 2500, and 3500 models) keyless entry remote fob

You can program your 2008, 2009, 2010 GMC Savana Van (including 1500, 2500, and 3500 models) remote yourself at home with these simple instructions.

This is the programming if you have the driver information center seen above.
(There is also a video to show you how easy this is done)
Switch ignition ON.
Press vehicle information button Fig. 2 [A] until PRESS TO RELEARN REMOTE KEY is displayed.
Press set/reset button Fig. 2 [B] until REMOTE KEY LEARNING ACTIVE is displayed.
Programming mode activated, proceed as follows:
Press and hold LOCK and UNLOCK buttons on first remote transmitter simultaneously for 15 seconds.
Wait for acoustic signal (indicates correct programming).
Repeat above procedure to program remaining remote transmitters.
Switch ignition OFF to exit programming mode.
Remote transmitters can also be programmed using diagnostic equipment.
NOTE: A maximum of 8 remote transmitters can be programmed.

How – without Driver Information Center (DIC)
Ensure vehicles with automatic transmission in park.
Switch ignition ON.
Press trip/odometer reset button until RELEARN REMOTE KEY is displayed Fig. 3 .
Press and hold trip/odometer reset button for 3 seconds, REMOTE KEY LEARNING ACTIVE is displayed Fig. 3 .
Programming mode activated, proceed as follows:
Press and hold LOCK and UNLOCK buttons on first remote transmitter simultaneously for 15 seconds.
Wait for acoustic signal (indicates correct programming).
Repeat above procedure to program remaining remote transmitters.
Switch ignition OFF to exit programming mode.
Remote transmitters can also be programmed using diagnostic equipment.
NOTE: A maximum of 8 remote transmitters can be programmed.

1997, 1998, 1999, 2000, 2001, and 2002 GMC Savana Van free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1997, 1998, 1999, 2000, 2001, and 2002 GMC Savana Van replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

1. Locate the Data Line Connector (DLC) underneath the driver’s side dashboard. Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
Use a jumper wire
to connect pins 4 & 8

2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (you can use a piece of thin electrical cable, speaker cable or simply U shaped paper clip; leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by cycling the locks (locking then unlocking doors) to signify entering of programming mode.
Figure a. Data link connector
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).

Free programming instructions for 2000, 2001, 2002, 2003, 2004 and 2005 GMC Safari Van replacement remote keyless entry fob alarm

This is how to program your 2000, 2001, 2002, 2003, 2004 and 2005 GMC Safari Van replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

1997, 1998, and 1999 GMC Safari Van free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1997, 1998, and 1999 GMC Safari Van replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

1. Locate the Data Line Connector (DLC) underneath the driver’s side dashboard. Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
Use a jumper wire
to connect pins 4 & 8

2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (you can use a piece of thin electrical cable, speaker cable or simply U shaped paper clip; leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond by cycling the locks (locking then unlocking doors) to signify entering of programming mode.
Figure a. Data link connector
3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 15 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).

Free programming instructions for 1997, 1998, 1999, 2000, 2001, 2002, 2003, and 2004 GMC Jimmy replacement remote keyless entry fob alarm

This is how to program your 1997, 1998, 1999, 2000, 2001, 2002, 2003, and 2004 GMC Jimmy replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

Free programming instructions for 1998, 1999, 2000, 2002, 2003, 2004, 2005, 2006, 2007, 2008, and 2009 GMC Envoy replacement remote keyless entry fob alarm

This is how to program your 1998, 1999, 2000, 2002, 2003, 2004, 2005, 2006, 2007, 2008, and 2009 GMC Envoy replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, and 2012 GMC Canyon small pickup truck keyless entry remote fob free programming information

Unfortunately, there are no do it yourself instructions that will work to program the 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, and 2012 GMC Canyon small pickup truck keyless entry remote.
This remote must be programmed by a Chevy/GM/GMC dealer or a professional automotive locksmith.