Free programming instructions for 2005, 2006, 2007, and 2008, Mazda RX-8 keyless entry remote fob alarm

You can program the remote portion of your 2005, 2006, 2007, and 2008, Mazda RX-8 remote key yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2004 and 2005 Mazda RX-8 keyless entry remote fob alarm

You can program your 2004 and 2005 Mazda RX-8 remote yourself at home with these simple instructions.

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

2008 and 2009 Mazda Tribute IKT remote head key keyless entry fob alarm free programming instructions

Once the key has been cut by a Mazda dealer or a locksmith, you can program the 2008 and 2009 Mazda Tribute IKT remote key yourself at home IF YOU HAVE TWO WORKING/PROGRAMMED KEYS already.
If you do not have two working/programmed keys, you will have to take this remote key to a dealer or locksmith for programming.

Please read and understand the
entire procedure before you begin.
1. Insert the first previously
programmed coded key into the
ignition.
2. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
3. Turn the ignition to the 1 (LOCK) position and remove the first coded
key from the ignition.
4. Within ten seconds of turning the ignition to the 1 (LOCK) position,
insert the second previously coded key into the ignition.
5. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least three seconds, but
no more than 10 seconds.
6. Turn the ignition to the 1 (LOCK) position and remove the second
previously programmed coded key from the ignition.
7. Within twenty seconds of turning the ignition to the 1 (LOCK)
position and removing the previously programmed coded key, insert the
new unprogrammed key (new key/valet key) into the ignition.
8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position.
Keep the ignition in the 3 (RUN) position for at least six seconds.
9. Remove the newly programmed coded key from the ignition.
If the key has been successfully programmed it will start the vehicle’s
engine and will operate the remote entry system (if the new key is an
Integrated Keyhead Transmitter). The theft indicator light will illuminate
for three seconds and then go out to indicate successful programming.

Free programming instructions for 2001, 2002, 2003, 2004, 2005, 2006, and 2007 Mazda Tribute keyless entry remote fob alarm

How to program your 2001, 2002, 2003, 2004, 2005, 2006, and 2007 Mazda Tribute Truck remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free programming instructions for 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mazda MX-5 Miata keyless entry remote fob alarm

You can program the remote portion of your 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mazda MX-5 Miata remote key yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2007, 2008, 2009, 2010, 2011, 2012 and 2013 Mazda CX-9 keyless entry remote fob alarm (with or without power liftgate)

You can program the remote portion of your 2007, 2008, 2009, 2010, 2011, 2012 and 2013 Mazda CX-9 (with or without power liftgate) remote key yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2007, 2008, 2009, 2010, 2011, and 2012 Mazda CX-7 keyless entry remote fob alarm

You can program the remote portion of your 2007, 2008, 2009, 2010, 2011, and 2012 Mazda CX-7 remote yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.