Free programming instructions for 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, and 2009 Mazda B – Series Truck keyless entry remote fob alarm

How to program your 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, and 2009 Mazda B – Series Truck remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a video below that will show you how this is done!

Turn the ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN.
All doors will lock then unlock to confirm programming mode.
Within 20 seconds,
press any button on 1st remote transmitter. Door locks will cycle to confirm programming.
Within 20 seconds, press any button on 2nd transmitter (up to 4 transmitters total possible).
Turn the ignition OFF. Locks will again cycle to indicate end of programming mode.

Free programming instructions for 2006, 2007, and 2008 Mazda 6 Hatchback keyless entry remote fob alarm

You can program the remote portion of your 2006, 2007, and 2008 Mazda 6 Hatchback remote yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2003, 2004, and 2005 Mazda 6 Hatchback keyless entry remote fob alarm

You can program your 2003, 2004, and 2005 Mazda 6 Hatchback remote yourself at home with these simple instructions.

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mazda 6 Sedan keyless entry remote fob alarm

You can program the remote portion of your 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mazda 6 Sedan remote yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2003, 2004, and 2005 Mazda 6 Sedan keyless entry remote fob alarm

You can program your 2003, 2004, and 2005 Mazda 6 Sedan remote yourself at home with these simple instructions.

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mazda 5 keyless entry remote fob alarm

You can program the remote portion of your 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mazda 5 remote yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2010, 2011, 2012, and 2013 Mazda 3 keyless entry remote fob alarm

You can program the remote portion of your 2010, 2011, 2012, and 2013 Mazda 3 remote yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

**THIS PROGRAMMING METHOD WILL NOT PROGRAM THE SMART KEY UNIT**

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2004, 2005, 2006, 2007, 2008, 2009 Mazda 3 keyless entry remote fob alarm

You can program your 2004, 2005, 2006, 2007, 2008, 2009 Mazda 3 remote yourself at home with these simple instructions.

**There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.

Free programming instructions for 2011, 2012, and 2013 Mazda 2 keyless entry remote fob alarm

You can program the remote portion of your 2011, 2012, and 2013 Mazda 2 remote yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a Mazda Dealer or an automotive locksmith.

There is also a free programming tutorial video below to show you how easy it is done.

NOTE: A maximum of 3 key remote transmitters can be programmed.
Obtain all key remote transmitters.
Remove key from ignition switch.
Close all doors.
Open driver’s door.
Carry out the following procedure within 24 seconds:
Turn ignition switch ON and back to LOCK position 3 times.
Close and then open the door 3 times (ending with door open)
Ensure doors lock and unlock.
If not, wait 40 seconds and repeat procedure starting with driver’s door already open.
Press UNLOCK button of each key remote transmitter twice.
Ensure doors lock and unlock after each operation.
If not, proceed as follows:
Open and close driver’s door once.
Ensure doors lock and unlock twice.
Repeat procedure starting with driver’s door already open.