Free Programming instructions for 2002, 2003, 2004, 2005, and 2006 Mitsubishi Outlander remote keyless entry fob alarm

How to program your 2002, 2003, 2004, 2005, and 2006 Mitsubishi Outlander remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes

1. Switch ignition OFF
2. Access the programming connector DLC (located in drivers side fascia)
(To see a picture of the Data Link Connector, you can click on the link below)
3. Jump programming connector terminals 1 and 4 (or ground)
4. Within 10 seconds press hazard switch 6 times
5. Doors should lock and unlock to confirm programming mode
6 Press and release remote transmitter LOCK button
7 Within 10 seconds press remote transmitter LOCK button twice
8 Doors should lock and unlock to confirm programming
9 If programming additional remotes within 1 minute repeat button procedure ( #6 ) for each additional remotes
10 To exit programming mode remove key from ignition or jump lead

http://blog.carandtruckremotes.com/2012/06/06/what-is-a-data-link-connector-also-called-the-dlc/

Free Programming instructions for 2007, 2008, 2009, 2010, 2011, and 2012 Mitsubishi Lancer remote portion of integrated key fob alarm

Once you have a working programmed key that will start the car, you can program the remote portion of this key yourself at home. This method will only program the remote buttons. You must still take the key to a dealer or locksmith to be cut and programmed to start the car.
This will program the remote buttons for 2007, 2008, 2009, 2010, 2011, and 2012 Mitsubishi Lancer remote head key.

Be sure you have all remotes with you at the time of programming:
1. Switch ignition OFF
2. Access the programming connector DLC (located in drivers side fascia)
(To see a picture of the Data Link Connector, you can click on the link below)
3. Jump programming connector terminals 1 and 4 (or ground)
4. Within 10 seconds press hazard switch 6 times
5. Doors should lock and unlock to confirm programming mode
6 Press and release remote transmitter LOCK button
7 Within 10 seconds press remote transmitter LOCK button twice
8 Doors should lock and unlock to confirm programming
9 If programming additional remotes within 1 minute repeat button procedure ( #6 ) for each additional remotes
10 To exit programming mode remove key from ignition or jump lead

http://blog.carandtruckremotes.com/2012/06/06/what-is-a-data-link-connector-also-called-the-dlc/

Free Programming instructions for 2002, 2003, 2004, 2005, and 2006 Mitsubishi Lancer remote keyless entry fob alarm

How to program your 2002, 2003, 2004, 2005, and 2006 Mitsubishi Lancer remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes

1. Switch ignition OFF
2. Access the programming connector DLC (located in drivers side fascia)
(To see a picture of the Data Link Connector, you can click on the link below)
3. Jump programming connector terminals 1 and 4 (or ground)
4. Within 10 seconds press hazard switch 6 times
5. Doors should lock and unlock to confirm programming mode
6 Press and release remote transmitter LOCK button
7 Within 10 seconds press remote transmitter LOCK button twice
8 Doors should lock and unlock to confirm programming
9 If programming additional remotes within 1 minute repeat button procedure ( #6 ) for each additional remotes
10 To exit programming mode remove key from ignition or jump lead

http://blog.carandtruckremotes.com/2012/06/06/what-is-a-data-link-connector-also-called-the-dlc/

Free Programming instructions for 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mitsubishi Galant remote portion of integrated key fob alarm

Once you have a working programmed key that will start the car, you can program the remote portion of this key yourself at home. This method will only program the remote buttons. You must still take the key to a dealer or locksmith to be cut and programmed to start the car.
This will program the remote buttons for 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mitsubishi Galant remote head key.

Be sure you have all remotes with you at the time of programming:
1. Switch ignition OFF
2. Access the programming connector DLC (located in drivers side fascia)
(To see a picture of the Data Link Connector, you can click on the link below)
3. Jump programming connector terminals 1 and 4 (or ground)
4. Within 10 seconds press hazard switch 6 times
5. Doors should lock and unlock to confirm programming mode
6 Press and release remote transmitter LOCK button
7 Within 10 seconds press remote transmitter LOCK button twice
8 Doors should lock and unlock to confirm programming
9 If programming additional remotes within 1 minute repeat button procedure ( #6 ) for each additional remotes
10 To exit programming mode remove key from ignition or jump lead

http://blog.carandtruckremotes.com/2012/06/06/what-is-a-data-link-connector-also-called-the-dlc/

Free Programming instructions for 1999, 2000, 2001, 2002, 2003, 2004, and 2005 Mitsubishi Galant remote keyless entry fob alarm

How to program your 1999, 2000, 2001, 2002, 2003, 2004, and 2005 Mitsubishi Galant remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes

1. Switch ignition OFF
2. Access the programming connector DLC (located in drivers side fascia)
(To see a picture of the Data Link Connector, you can click on the link below)
3. Jump programming connector terminals 1 and 4 (or ground)
4. Within 10 seconds press hazard switch 6 times
5. Doors should lock and unlock to confirm programming mode
6 Press and release remote transmitter LOCK button
7 Within 10 seconds press remote transmitter LOCK button twice
8 Doors should lock and unlock to confirm programming
9 If programming additional remotes within 1 minute repeat button procedure ( #6 ) for each additional remotes
10 To exit programming mode remove key from ignition or jump lead

http://blog.carandtruckremotes.com/2012/06/06/what-is-a-data-link-connector-also-called-the-dlc/

Free Programming instructions for 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mitsubishi Eclipse remote portion of integrated key fob alarm

Once you have a working programmed key that will start the car, you can program the remote portion of this key yourself at home. This method will only program the remote buttons. You must still take the key to a dealer or locksmith to be cut and programmed to start the car.
This will program the remote buttons for 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Mitsubishi Eclipse remote head key.

Be sure you have all remotes with you at the time of programming:
1. Switch ignition OFF
2. Access the programming connector DLC (located in drivers side fascia)
(To see a picture of the Data Link Connector, you can click on the link below)
3. Jump programming connector terminals 1 and 4 (or ground)
4. Within 10 seconds press hazard switch 6 times
5. Doors should lock and unlock to confirm programming mode
6 Press and release remote transmitter LOCK button
7 Within 10 seconds press remote transmitter LOCK button twice
8 Doors should lock and unlock to confirm programming
9 If programming additional remotes within 1 minute repeat button procedure ( #6 ) for each additional remotes
10 To exit programming mode remove key from ignition or jump lead

http://blog.carandtruckremotes.com/2012/06/06/what-is-a-data-link-connector-also-called-the-dlc/

Free Programming instructions for 2000, 2001, 2002, and 2003 Mitsubishi Eclipse remote keyless entry fob alarm

How to program your 2000, 2001, 2002, and 2003 Mitsubishi Eclipse remote keyless entry fob alarm by yourself at home without going to the dealer.

2000 2001 2002 2003 Mitsubishi Eclipse

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes

1. Switch ignition OFF
2. Access the programming connector DLC (located in drivers side fascia)
(To see a picture of the Data Link Connector, you can click on the link below)
3. Jump programming connector terminals 1 and 4 (or ground)
4. Within 10 seconds press hazard switch 6 times
5. Doors should lock and unlock to confirm programming mode
6 Press and release remote transmitter LOCK button
7 Within 10 seconds press remote transmitter LOCK button twice
8 Doors should lock and unlock to confirm programming
9 If programming additional remotes within 1 minute repeat button procedure ( #6 ) for each additional remotes
10 To exit programming mode remove key from ignition or jump lead

http://blog.carandtruckremotes.com/2012/06/06/what-is-a-data-link-connector-also-called-the-dlc/