Free Programming instructions for 2000, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Nissan Xterra remote keyless entry fob alarm

How to program your 2000, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Nissan Xterra remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a tutorial video below to show you how easily it is done!

PLEASE READ CAREFULLY BEFORE TRYING! IF AT ANY TIME YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER.
THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY

1. SIT IN CAR WITH DOORS AND WINDOWS CLOSED.
2. LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER’S DOOR.
3. PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC
4. WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD) , PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote)
5. PRESS LOCK BUTTON ON THE NEW REMOTE, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6. PRESS UNLOCK BUTTON ON DRIVER’S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH
7. PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can’t get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in – shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition

Free Programming instructions for 2007, 2008, 2009, 2010, 2011, and 2012 Nissan Versa remote keyless entry fob alarm

How to program your 2007, 2008, 2009, 2010, 2011, and 2012 Nissan Versa remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a tutorial video below to show you how easily it is done!

PLEASE READ CAREFULLY BEFORE TRYING! IF AT ANY TIME YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER.
THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY

1. SIT IN CAR WITH DOORS AND WINDOWS CLOSED.
2. LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER’S DOOR.
3. PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC
4. WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD) , PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote)
5. PRESS LOCK BUTTON ON THE NEW REMOTE, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6. PRESS UNLOCK BUTTON ON DRIVER’S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH
7. PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can’t get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in – shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition

Free Programming instructions for 2008, 2009, 2010, 2011, and 2012 Nissan Rogue remote portion of integrated key fob alarm

Once you have a working programmed key that will start the car, you can program the remote portion of this key yourself at home. This method will only program the remote buttons. You must still take the key to a dealer or locksmith to be cut and programmed to start the car.
This will program the remote buttons for 2008, 2009, 2010, 2011, and 2012 Nissan Rogue remote head key.

There is even a tutorial video below to show you how easily it is done!

PLEASE READ CAREFULLY BEFORE TRYING! IF AT ANY TIME YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER.
THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY

1. SIT IN CAR WITH DOORS AND WINDOWS CLOSED.
2. LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER’S DOOR.
3. PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC
4. WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD) , PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote)
5. PRESS LOCK BUTTON ON THE NEW REMOTE, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6. PRESS UNLOCK BUTTON ON DRIVER’S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH
7. PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can’t get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in – shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition

Free Programming instructions for 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Nissan Titan remote keyless entry fob alarm

How to program your 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Nissan Titan remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a tutorial video below to show you how easily it is done!

PLEASE READ CAREFULLY BEFORE TRYING! IF AT ANY TIME YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER.
THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY

1. SIT IN CAR WITH DOORS AND WINDOWS CLOSED.
2. LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER’S DOOR.
3. PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC
4. WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD) , PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote)
5. PRESS LOCK BUTTON ON THE NEW REMOTE, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6. PRESS UNLOCK BUTTON ON DRIVER’S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH
7. PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can’t get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in – shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition

2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Nissan Sentra smart key remote keyless entry fob alarm programming information

Unfortunately, there are no do it yourself instructions that will work to program the 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Nissan Sentra smart key key less entry remote fobs.
This remote must be programmed by an Nissan dealer or a professional automotive locksmith.

Free Programming instructions for 2013, 2014, and 2015 Nissan Sentra remote portion of integrated key fob alarm

Once you have a working programmed key that will start the car, you can program the remote portion of this key yourself at home. This method will only program the remote buttons. You must still take the key to a dealer or locksmith to be cut and programmed to start the car.
This will program the remote buttons for 2013, 2014, and 2015 Nissan Sentra remote head key.

There is even a tutorial video below to show you how easily it is done!

PLEASE READ CAREFULLY BEFORE TRYING! IF AT ANY TIME YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER.
THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY

1. SIT IN CAR WITH DOORS AND WINDOWS CLOSED.
2. LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER’S DOOR.
3. PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC
4. WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD) , PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote)
5. PRESS LOCK BUTTON ON THE NEW REMOTE, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6. PRESS UNLOCK BUTTON ON DRIVER’S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH
7. PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can’t get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in – shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition

Free Programming instructions for 2000, 2001, 2002, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Nissan Sentra remote keyless entry fob alarm

How to program your 2000, 2001, 2002, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, and 2012 Nissan Sentra remote keyless entry fob alarm by yourself at home without going to the dealer.

There is even a tutorial video below to show you how easily it is done!

PLEASE READ CAREFULLY BEFORE TRYING! IF AT ANY TIME YOU MAKE A MISTAKE, START AND STOP YOUR CAR, EXIT THE VEHICLE AND START OVER.
THE REMOTE CAN BE ONLY PROGRAMMED WITH A MASTER KEY

1. SIT IN CAR WITH DOORS AND WINDOWS CLOSED.
2. LOCK DOORS WITH POWER DOOR LOCK SWITCH ON DRIVER’S DOOR.
3. PUT IN AND PULL OUT KEY FROM IGNITION APPROX. 8 TIMES OR UNTIL YOU SEE THE HAZARD/TURN SIGNAL LIGHTS FLASH.(older models lights may flash after 4 or 5 times) YOU NEED TO DO THAT IN LESS THEN 10 SEC
4. WHEN HAZARD LIGHTS FLASH (ON 2005 AND NEWER MODELS THE GAUGE NEEDLES MAY JUMP A LITTLE INSTEAD) , PUT KEY IN IGNITION AND TURN TO THE ACC POSITION.(when your hazard lights flash your car is sending a signal to be received by the remote)
5. PRESS LOCK BUTTON ON THE NEW REMOTE, LIGHTS SHOULD FLASH AGAIN.

IF YOU HAVE 2 REMOTES, 1 NEW AND 1 OLD OR 2 NEW ONES, PLEASE CONTINUE WITH STEPS 6 AND 7. IF NOT, SKIP TO END.

6. PRESS UNLOCK BUTTON ON DRIVER’S DOOR, THEN LOCK BUTTON ON DRIVERS DOOR, LIGHTS WILL AGAIN FLASH
7. PRESS LOCK BUTTON ON 2ND NEW OR OLD REMOTE. LIGHTS AGAIN WILL FLASH.

YOU ARE DONE. EXIT VEHICLE AND TRY YOUR REMOTE. IT WILL NOT WORK FROM INSIDE CAR OR WITH KEY IN IGNITION.

Note: if your hazard lights flash after inserting your key in and out, but you can’t get the remote to program, you may have a dead battery or the wrong remote. If instructions do not work, do it again but when you get in – shut the door, buckle seat belt and lock doors, then proceed to putting key in ignition