1998, 1999, 2000, 2001, 2002, 2003, and 2004 Oldsmobile Bravada free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1998, 1999, 2000, 2001, 2002, 2003, and 2004 Oldsmobile Bravada replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a free programming tutorial video below to show you how easy it is done.

Obtain all remote transmitters.
Close all doors.
Insert key into ignition, do not turn ignition switch.
Press and hold door lock switch in the unlock position.
Switch ignition ON, OFF, ON, OFF.
Release door lock switch.
Doors will lock and unlock, indicating programming mode activated.
To program remote transmitter proceed as follows:
Simultaneously press and hold transmitter LOCK and UNLOCK buttons.
Doors will lock and unlock, indicating remote transmitter programmed.
Repeat above procedure for each remote transmitter.
Switch ignition ON to exit programming mode.
NOTE: Existing remote transmitter memory positions will be overwritten.
NOTE: A maximum of 4 remote transmitters can be programmed.

FREE keyless entry remote fob programming instructions for 1997, 1998, 1999, 2000, 2001, 2002, 2003, and 2004 Oldsmobile Silhouette

This is how to program your 1997, 1998, 1999, 2000, 2001, 2002, 2003, and 2004 Oldsmobile Silhouette keyless entry remote yourself at home without going to the dealer…

Have all remotes with you during programming procedure.
1. Remove key from ignition switch
2. Remove the “BCM PRGRM” fuse from the fuse box
3. Close all doors
4. Turn ignition switch to the “ACC” position
5. Within 1 second, turn the ignition switch “OFF” and then back to “ACC”
6. To program the remote proceed as follows:
*Press and hold the Lock and Unlock buttons on the remote simultaneously until a chime sounds,
approximately 14 Seconds.
7. Repeat step 6 for each additional remote transmitter you have.
8. Remove key from ignition switch
9. Refit the “BCM PRGRM” fuse into the fuse box.

FREE keyless entry remote fob programming instructions for 1997, 1998, 1999, 2000, 2001, and 2002 Oldsmobile Intrigue

This is how to program your 1997, 1998, 1999, 2000, 2001, and 2002 Oldsmobile Intrigue keyless entry remote yourself at home without going to the dealer…

Be sure to have all the remotes with you at time of procedure.
1. Sit in driver’s seat
2. Close all doors
3. Press and hold UNLOCK button switch on the door and keep holding it down until step 6
4. Insert and remove ignition key twice. Do not turn the key.
5. Insert the key a third time and leave it in the ignition switch. Do not turn the key.
6. Release the door unlock switch. A chime will sound 3 times indicating that programming mode is active.
7. Press and hold the Lock and Unlock buttons on the remote at the same time for 12 seconds or so or until the car chimes again twice indicating the remote has been programmed successfully.
8. Repeat step 7 for each additional remote.
9. Remove key from ignition switch to exit programming mode.

FREE keyless entry remote fob programming instructions for 1996, 1997, 1998, and 1999 Oldsmobile Aurora

This is how to program your 1996, 1997, 1998, and 1999 Oldsmobile Aurora keyless entry remote yourself at home without going to the dealer…

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again.

1. Ignition OFF .Locate the Data Line Connector (DLC) Use the figure below as a map for your DLC (they usually aren’t numbered). The view in the picture below is looking straight into the cavities of the DLC. Notice how the DLC is tapered on both ends; we will be working on the wider row of cavities (1 through 8 in the figure below).
Use a jumper wire
to connect pins 4 & 8
2. Make sure there are metal contact pins in terminals 8 and 4 and connect the Data Line Connector (DLC) terminal 8 to terminal 4 with a suitable jumper wire (leave the jumper wire connected throughout the programming procedure). Make sure you know which terminals are 8 and 4.
3. Switch ignition ON
Figure a. Data link connector
4. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to be programmed. After about 30 seconds, the vehicle will respond by cycling the locks (locking then unlocking doors). Release the buttons on the transmitter.
4. Within one minute, repeat the previous step on the remaining transmitters to be programmed.
5. Remove jumper wire applied to the DLC (disconnect terminals 8 and 4).

FREE keyless entry remote fob programming instructions for 1999 and 2000 Oldsmobile Alero

This is how to program your 1999 and 2000 Oldsmobile Alero keyless entry remote yourself at home without going to the dealer…

Obtain all remote transmitters
Access the programming connector (a single black wire, located behind the panel in the RH trunk)
Jump programming connector to ground
System should not lock and unlock doors to indicate programming mode is actived
* Press and hold Lock and Unlock buttons (at the same time) on remote for approximately 10 seconds.
* System will lock and unlock indicating remote transmitter programmed
Repeat above * procedure for all other remote transmitters
Remove programming connector wire to exit programming mode
-Any existing remotes not programmed during this procedure will be overwritten
-You can have up to 4 transmitters active at one time on this system