2009 and 2010 Pontiac Vibe keyless entry remote fob alarm free programming instructions

You can program the remote portion of your 2009 and 2010 Pontiac Vibe remote yourself at home with these simple instructions.

**You will still need to take the key to be cut and have transponder chip programmed to start the car. Cutting and programming of the KEY portion must be done by a GM Dealer or an automotive locksmith.

There is also a free programming tutorial video below to show you how easy it is done.

1. Driver door open and unlocked. Key out of the ignition
2. Insert the key and remove 2 times in 5 seconds
3. Close and open drivers door 2 times in 40 sec.
4. Insert the key and remove it from ignition again
5. Close and open drivers door 2 times in 40 sec.
6. Insert the key in ignition
7. Close the door
8. Turn to ON can back to LOCK in 1 second intervals. 1 time for ADD, 2 times for REWRITE
9. Remove the key
10. Power locks will cycle to confirm
11. For ADD or REWRITE mode within 40 sec. Of the confirmation,
A Press lock and unlock buttons of the fob at the same time between 1 and 1.5 seconds
B within 3 sec press lock button for more then 1 sec and release
C If it’s correct the power locks will cycle again. If it is not please try the procedure again

2003, 2004, 2005, 2006, 2007, and 2008 Pontiac Vibe free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2003, 2004, 2005, 2006, 2007, and 2008 Pontiac Vibe replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a free programming tutorial video below to show you how easy it is done.

1. Driver door open and unlocked. Key out of the ignition
2. Insert the key and remove 2 times in 5 seconds
3. Close and open drivers door 2 times in 40 sec.
4. Insert the key and remove it from ignition again
5. Close and open drivers door 2 times in 40 sec.
6. Insert the key in ignition
7. Close the door
8. Turn to ON can back to LOCK in 1 second intervals. 1 time for ADD, 2 times for REWRITE
9. Remove the key
10. Power locks will cycle to confirm
11. For ADD or REWRITE mode within 40 sec. Of the confirmation,
A Press lock and unlock buttons of the fob at the same time between 1 and 1.5 seconds
B within 3 sec press lock button for more then 1 sec and release
C If it’s correct the power locks will cycle again. If it is not please try the procedure again

2007, 2008, and 2009 Pontiac Torrent free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2007, 2008, and 2009 Pontiac Torrent replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a free programming tutorial video below to show you how easy it is done.

Switch ignition ON.
Repeatedly press vehicle information button Fig. 2 [A] until PRESS TO RELEARN REMOTE KEY is displayed.
Press set/reset button Fig. 2 [B] until REMOTE KEY LEARNING ACTIVE is displayed.
Programming mode activated, proceed as follows:
Press and hold LOCK and UNLOCK buttons on first remote transmitter simultaneously for 15 seconds.
Wait for acoustic signal (indicates correct programming).
Repeat above procedure to program remaining remote transmitters.
Switch ignition OFF to exit programming mode.
Remote transmitters can also be programmed using diagnostic equipment.
NOTE: A maximum of 8 remote transmitters can be programmed.

FREE keyless entry remote fob programming instructions for 1997 and 1998 Pontiac Trans Sport

This is how to program your 1997 and 1998 Pontiac Trans Sport keyless entry remote yourself at home without going to the dealer…

1. Remove the ignition key from the ignition lock cylinder.

2. Remove the “BCM PRGRM” fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the “BCMPRGRM” fuse.

3. Close all of the doors.

4. Close the liftgate.

5. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you – the opposite direction from starting the engine).

6. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second (the quicker the better)

7. Open and close any vehicle door. A chime will be heard when the system enters the programming mode.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming. Your new remote has been accepted and all existing remote codes have been erased.

9. Repeat the previous step on each additional transmitter to be programmed (including any existing transmitters). Just repeat step #9 for each remote you want to
program. Don’t repeat all nine steps for each remote

10. Remove the ignition key from the ignition lock cylinder.

11. Install the “BCM PRGRM” fuse back into the fuse panel.

FREE keyless entry remote fob programming instructions for 1997, 1998, and 1999 Pontiac Sunfire

This is how to program your 1997, 1998, and 1999 Pontiac Sunfire keyless entry remote yourself at home without going to the dealer…

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes
1. Switch ignition OFF
2. Access the programming connector (located in LH trunk)
3. Jump (connect) programming connector terminals (you can use paper clip or wire) If you will pull the liner from behind the left rear taillights on driver side of car you will see a small plug inline that leads to a small black box on wheel well which is the receiver for the keyless remote
4. System should now lock and unlock doors, trunk and chirp horn to indicate programming mode activated
5. Proceed as follows:
A Press and hold LOCK and UNLOCK buttons on remote for up to 15 seconds
B System should lock and unlock doors, trunk and chirp horn to indicate remote programmed
6 Repeat above procedure for other additional remotes
7 Remove programming connector jumper clip or wire to exit programming mode

FREE keyless entry remote fob programming instructions for 1999, 2000, 2001, 2002, 2003, 2004, and 2005 Pontiac Montana

This is how to program your 1999, 2000, 2001, 2002, 2003, 2004, and 2005 Pontiac Montana keyless entry remote yourself at home without going to the dealer…

1. Remove the ignition key from the ignition lock cylinder.

2. Remove the “BCM PRGRM” fuse from the fuse panel, accessed by opening the front passenger door. Use the legend on the fuse panel to properly locate the “BCMPRGRM” fuse.

3. Close all of the doors.

4. Close the liftgate.

5. Insert keys into the ignition, and turn the ignition lock cylinder to ACC (one click towards you – the opposite direction from starting the engine).

6. Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second (the quicker the better)

7. Open and close any vehicle door. A chime will be heard when the system enters the programming mode.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. IMPORTANT: After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming. Your new remote has been accepted and all existing remote codes have been erased.

9. Repeat the previous step on each additional transmitter to be programmed (including any existing transmitters). Just repeat step #9 for each remote you want to
program. Don’t repeat all nine steps for each remote

10. Remove the ignition key from the ignition lock cylinder.

11. Install the “BCM PRGRM” fuse back into the fuse panel.