2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Toyota Tacoma free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015 Toyota Tacoma replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a video below the written instructions that shows how easy this is done.

Driver’s door open, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.
Within 40 seconds:
Close and open driver’s door twice.
Insert and remove the key from the ignition switch.
Within 40 seconds:
Close and open driver’s door twice.
Insert the key into the ignition switch and close the driver’s door.
Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program a remote transmitter code whilst erasing the original codes.
Remove key from ignition switch:
System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered.
Within 40 seconds:
Press and hold LOCK and UNLOCK remote buttons simultaneously for 1.5 seconds
Within 3 seconds:
Press LOCK button.
System should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed.
Within 40 seconds:
Repeat button procedure to program remaining remote transmitters.
NOTE: To exit programming mode: Open driver’s door. NOTE: A maximum of 4 remote transmitters can be programmed.

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tacoma-remotes.html

2002, 2003, and 2004 Toyota Tacoma free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2002, 2003, and 2004 Toyota Tacoma replacement remote keyless entry fob alarm by yourself at home without going to the dealer. This is for the dealer installed remote keyless system.

MPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes

1. Driver’s door open, all other doors closed, key removed from ignition switch
2. Insert key into ignition switch, then remove it
3. Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.
4. Close and reopen driver’s door
5. Press LOCK and UNLOCK on the vehicle door lock control at 1 second intervals 5 times.
6. Insert key into ignition switch
7. Switch ignition ON and OFF once to program a remote code while retaining the original codes, twice to program a remote transmitter code while erasing the original codes. Three times to check how many remote transmitters are currently registered or five times to erase all codes
8. Remove key from ignition switch. System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. One to 4 times slowly, to indicate number of remotes registered
9. Press and hold remote LOCK button and UNLOCK buttons together for 1-1.5 second
10. Press LOCK remote button for 1 second: system should lock and unlock vehicle one to confirm, twice to indicate registration has failed
11. If required repeat button procedure to program remaining remotes
NOTE To exit programming mode – close drivers door or insert ignition key

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tacoma-remotes.html

1995, 1996, 1997, 1998, 1999, 2000, and 2001 Toyota Tacoma free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1995, 1996, 1997, 1998, 1999, 2000, and 2001 Toyota Tacoma replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

I. To program (add) a REMOTE CONTROL to the system:
1. Insert the key into ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and release a REMOTE
CONTROL’s top or bottom
button.*
The STATUS MONITOR LED
turns off.
The Piezo “chirper” chirps once.
The exterior lights flash once.
4. Turn off the ignition. The ECU will
now operate with the REMOTE
CONTROL just programmed.
* Either button on your REMOTE CONTROL can be programmed to operate the system. The bottom
button can be programmed to operate a second vehicle with the Toyota VIP.
Programming
Procedure
Press and Hold
for 3 Seconds
Lights Up
Press Once

II. To erase all REMOTE CONTROL codes from the system:
1. Insert key into the ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and hold the ECU’s
PROGRAMMING SWITCH for
over 2 seconds again.
The STATUS MONITOR LED
turns off, then flashes 3 times.
The Piezo “chirper” chirps three
times and the exterior lights flash
3 times.
4. Turn off the ignition. The ECU has cleared all REMOTE CONTROL codes; until
another REMOTE CONTROL is programmed, the system will not work with any
REMOTE CONTROL.

rs3000_alarmbrain

rs3000_greenbutton

rs3000_ignition_off

rs3000_ignition_on

rs3000_remote

rs3000_securityled

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-tacoma-remotes.html

1991, 1992, 1993, 1994, 1995, 1996, 1997, and 1998 Toyota Supra free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1991, 1992, 1993, 1994, 1995, 1996, 1997, and 1998 Toyota Supra replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

I. To program (add) a REMOTE CONTROL to the system:
1. Insert the key into ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and release a REMOTE
CONTROL’s top or bottom
button.*
The STATUS MONITOR LED
turns off.
The Piezo “chirper” chirps once.
The exterior lights flash once.
4. Turn off the ignition. The ECU will
now operate with the REMOTE
CONTROL just programmed.
* Either button on your REMOTE CONTROL can be programmed to operate the system. The bottom
button can be programmed to operate a second vehicle with the Toyota VIP.
Programming
Procedure
Press and Hold
for 3 Seconds
Lights Up
Press Once

II. To erase all REMOTE CONTROL codes from the system:
1. Insert key into the ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and hold the ECU’s
PROGRAMMING SWITCH for
over 2 seconds again.
The STATUS MONITOR LED
turns off, then flashes 3 times.
The Piezo “chirper” chirps three
times and the exterior lights flash
3 times.
4. Turn off the ignition. The ECU has cleared all REMOTE CONTROL codes; until
another REMOTE CONTROL is programmed, the system will not work with any
REMOTE CONTROL.

rs3000_alarmbrain

rs3000_greenbutton

rs3000_ignition_off

rs3000_ignition_on

rs3000_remote

rs3000_securityled

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-supra-remotes.html

2004, 2005, 2006, 2007, and 2008 Toyota Solara free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2004, 2005, 2006, 2007, and 2008 Toyota Solara replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a video below the written instructions that shows how easy this is done.

Driver’s door open, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.
Within 40 seconds:
Close and open driver’s door twice.
Insert and remove the key from the ignition switch.
Within 40 seconds:
Close and open driver’s door twice.
Insert the key into the ignition switch and close the driver’s door.
Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program a remote transmitter code whilst erasing the original codes.
Remove key from ignition switch:
System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered.
Within 40 seconds:
Press and hold LOCK and UNLOCK remote buttons simultaneously for 1.5 seconds
Within 3 seconds:
Press LOCK button.
System should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed.
Within 40 seconds:
Repeat button procedure to program remaining remote transmitters.
NOTE: To exit programming mode: Open driver’s door. NOTE: A maximum of 4 remote transmitters can be programmed.

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-solara-remotes.html

1999, 2000, 2001, 2002, and 2003 Toyota Solara free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1999, 2000, 2001, 2002, and 2003 Toyota Solara replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehicle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will not be functional until you program the transmitters again. You can program up to 4 remotes

1. Driver’s door open, all other doors closed, key removed from ignition switch
2. Insert key into ignition switch, then remove it
3. Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.
4. Close and reopen driver’s door
5. Press LOCK and UNLOCK on the vehicle door lock control at 1 second intervals 5 times.
6. Insert key into ignition switch
7. Switch ignition ON and OFF once to program a remote code while retaining the original codes, twice to program a remote transmitter code while erasing the original codes. Three times to check how many remote transmitters are currently registered or five times to erase all codes
8. Remove key from ignition switch. System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. One to 4 times slowly, to indicate number of remotes registered
9. Press and hold remote LOCK button and UNLOCK buttons together for 1-1.5 second
10. Press LOCK remote button for 1 second: system should lock and unlock vehicle one to confirm, twice to indicate registration has failed
11. If required repeat button procedure to program remaining remotes
NOTE To exit programming mode – close drivers door or insert ignition key

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-solara-remotes.html

Free programming information for 2011, 2012, 2013, 2014, and 2015 Toyota Sienna CE, LE, and XLE remote fob alarm keyless entry remote key

Unfortunately, there are no do it yourself programming instructions that will work for the 2011, 2012, 2013, 2014, and 2015 Toyota Sienna CE, LE, and XLE remote keyless entry fob alarm.
You must take this remote to a Toyota dealer or local automotive locksmith for programming.

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-sienna-remotes.html

2004, 2005, 2006, 2007, 2008, 2009 and 2010 Toyota Sienna CE, LE, and XLE free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 2004, 2005, 2006, 2007, 2008, 2009 and 2010 Toyota Sienna CE, LE, and XLE replacement remote keyless entry fob alarm by yourself at home without going to the dealer.
There is also a video below the written instructions that shows how easy this is done.

Driver’s door open, key removed from ignition switch.
Within 5 seconds:
Insert and remove the key from the ignition switch twice.
Within 40 seconds:
Close and open driver’s door twice.
Insert and remove the key from the ignition switch.
Within 40 seconds:
Close and open driver’s door twice.
Insert the key into the ignition switch and close the driver’s door.
Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program a remote transmitter code whilst erasing the original codes.
Remove key from ignition switch:
System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered.
Within 40 seconds:
Press and hold LOCK and UNLOCK remote buttons simultaneously for 1.5 seconds
Within 3 seconds:
Press LOCK button.
System should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed.
Within 40 seconds:
Repeat button procedure to program remaining remote transmitters.
NOTE: To exit programming mode: Open driver’s door. NOTE: A maximum of 4 remote transmitters can be programmed.

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-sienna-remotes.html

1999, 2000, 2001, 2002, and 2003 Toyota Sienna free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1999, 2000, 2001, 2002, and 2003 Toyota Sienna replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

I. To program (add) a REMOTE CONTROL to the system:
1. Insert the key into ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and release a REMOTE
CONTROL’s top or bottom
button.*
The STATUS MONITOR LED
turns off.
The Piezo “chirper” chirps once.
The exterior lights flash once.
4. Turn off the ignition. The ECU will
now operate with the REMOTE
CONTROL just programmed.
* Either button on your REMOTE CONTROL can be programmed to operate the system. The bottom
button can be programmed to operate a second vehicle with the Toyota VIP.
Programming
Procedure
Press and Hold
for 3 Seconds
Lights Up
Press Once

II. To erase all REMOTE CONTROL codes from the system:
1. Insert key into the ignition switch,
and turn it to “ON”.
2. Press and hold the ECU’s
PROGRAMMING SWITCH for 3
seconds.
The STATUS MONITOR LED
turns on for 5 seconds.
NOTE:
YOU MUST PERFORM THE NEXT
STEP WITHIN 5 SECONDS.
3. Press and hold the ECU’s
PROGRAMMING SWITCH for
over 2 seconds again.
The STATUS MONITOR LED
turns off, then flashes 3 times.
The Piezo “chirper” chirps three
times and the exterior lights flash
3 times.
4. Turn off the ignition. The ECU has cleared all REMOTE CONTROL codes; until
another REMOTE CONTROL is programmed, the system will not work with any
REMOTE CONTROL.

rs3000_alarmbrain

rs3000_greenbutton

rs3000_ignition_off

rs3000_ignition_on

rs3000_remote

rs3000_securityled

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-sienna-remotes.html

1998 Toyota Sienna free programming instructions for replacement remote keyless entry fob alarm

This is how to program your 1998 Toyota Sienna replacement remote keyless entry fob alarm by yourself at home without going to the dealer.

Ensure key removed from ignition switch.
Locate central locking signal control module Fig. 1 [1].
With harness multi-plug still connected, jump harness multi-plug terminals 1 and 9:
System should now lock and unlock vehicle once.
Press any remote transmitter button:
System should now lock and unlock vehicle once to confirm.
Repeat button procedure to program second remote transmitter.
To exit programming mode: Remove jump lead from central locking signal control module harness multi-plug.
Refit all components in reverse order of removal.
NOTE: A maximum of 2 remote transmitters can be programmed.
NOTE: Programming remote transmitter erases all previous codes. Both remote transmitters must be programmed at the
same time.
Fig. 1 Fig. 2
1998 toyota sienna xle programming

For more information about these remotes, or to place an order, please click on the link below:
http://www.carandtruckremotes.com/toyota-remotes-sienna-remotes.html